Difference between revisions of "Huanyang HY Series VFDs"
(added Modbus link) |
(added stock photo) |
||
| (4 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| + | [[File:HuanYang_HY02D211B_Stock_Photo.jpg|thumb|HuanYang HY02D211B (stock photo)]] | ||
| + | |||
== Overview == | == Overview == | ||
| Line 24: | Line 26: | ||
[http://www.etech.net.au/Huanyang/HY%20Series%20Inverter%2020100627.pdf#page=11 Page 11] shows the description of the terminal blocks | [http://www.etech.net.au/Huanyang/HY%20Series%20Inverter%2020100627.pdf#page=11 Page 11] shows the description of the terminal blocks | ||
| + | |||
| + | Some models don't have two relay outputs, and the control terminal layout is different: | ||
| + | |||
| + | [https://bulkman3d.com/wp-content/uploads/2019/01/HY01D523B-VFD-Manual.pdf#page=8 Page 8] shows the description of the terminal blocks | ||
== Modbus control == | == Modbus control == | ||
| + | |||
| + | You must set the slave address to something valid (non-zero) and use some form of RTU mode instead of ASCII for most software stacks to communicate with the VFD: | ||
| + | |||
| + | {| class="wikitable" | ||
| + | ! Parameter | ||
| + | ! Default Value | ||
| + | ! Needed Value | ||
| + | ! Description | ||
| + | |- | ||
| + | | PD000 | ||
| + | | 1: parameter editing locked | ||
| + | | 0: parameter editing unlocked | ||
| + | | parameter editing lock | ||
| + | |- | ||
| + | | PD163 | ||
| + | | 0: invalid | ||
| + | | 1: address of 1 | ||
| + | | slave address | ||
| + | |- | ||
| + | | PD164 | ||
| + | | 1: 9,600 baud | ||
| + | | 1: 9,600 baud | ||
| + | | baud rate | ||
| + | |- | ||
| + | | PD165 | ||
| + | | 0: ASCII,8N1 | ||
| + | | 3: RTU,8N1 | ||
| + | | ASCII vs RTU,data bits,parity,stop bits | ||
| + | |} | ||
[http://www.etech.net.au/Huanyang/HY%20Series%20Inverter%2020100627.pdf#page=60 page 60] describes the Modbus protocol | [http://www.etech.net.au/Huanyang/HY%20Series%20Inverter%2020100627.pdf#page=60 page 60] describes the Modbus protocol | ||
| Line 34: | Line 69: | ||
https://www.exoror.com/datasheet/VFD.pdf | https://www.exoror.com/datasheet/VFD.pdf | ||
| + | |||
| + | https://bulkman3d.com/wp-content/uploads/2019/01/HY01D523B-VFD-Manual.pdf | ||
| + | |||
| + | https://www.nvcnc.net/wp-content/uploads/2021/06/HuanYang-VFD-Manual.pdf | ||
| + | |||
| + | http://www.jinlantrade.com/ebay/invertermanual.pdf | ||
[https://web.archive.org/web/20160910091142/http://hy-dq.cn/Products_e.asp?classid=1 Produts | Hyria Electric Co, LTD (Wayback Machine)] | [https://web.archive.org/web/20160910091142/http://hy-dq.cn/Products_e.asp?classid=1 Produts | Hyria Electric Co, LTD (Wayback Machine)] | ||
[https://web.archive.org/web/20110921032437/http://www.h-y.tw/ www.h-y.tw (Wayback Machine)] | [https://web.archive.org/web/20110921032437/http://www.h-y.tw/ www.h-y.tw (Wayback Machine)] | ||
| + | |||
| + | [https://github.com/GilchristT/SpindleTalker2/releases Releases · GilchristT/SpindleTalker2] | ||
| + | |||
| + | [https://github.com/RobertOlechowski/Huanyang_VFD RobertOlechowski/Huanyang_VFD: All you have to know about Huanyang VFD] | ||
[https://github.com/LinuxCNC/linuxcnc/tree/master/src/hal/user_comps/huanyang-vfd linuxcnc/src/hal/user_comps/huanyang-vfd at master · LinuxCNC/linuxcnc] | [https://github.com/LinuxCNC/linuxcnc/tree/master/src/hal/user_comps/huanyang-vfd linuxcnc/src/hal/user_comps/huanyang-vfd at master · LinuxCNC/linuxcnc] | ||
Latest revision as of 19:06, 28 February 2024
Overview
Variable frequency drive for 3-phase spindle motors. They are found on eBay, Amazon, AliExpress, etc, typically marketed for Chinese water cooled spindles.
Model Numbers
| Model | Input Power | Output Power |
|---|---|---|
| HY01D523B | 1PH/3PH 220VAC±20% 50Hz/60Hz | 3PH 0-220VAC 1.5kW 7A 0.5-400Hz |
| HY02D211B | 3PH 110VAC±20% 50Hz±5Hz | 3PH 0-110VAC 2.2kW 20A 0.5-400Hz |
Page 4 shows the model number scheme
Wiring Diagram
Page 11 shows the description of the terminal blocks
Some models don't have two relay outputs, and the control terminal layout is different:
Page 8 shows the description of the terminal blocks
Modbus control
You must set the slave address to something valid (non-zero) and use some form of RTU mode instead of ASCII for most software stacks to communicate with the VFD:
| Parameter | Default Value | Needed Value | Description |
|---|---|---|---|
| PD000 | 1: parameter editing locked | 0: parameter editing unlocked | parameter editing lock |
| PD163 | 0: invalid | 1: address of 1 | slave address |
| PD164 | 1: 9,600 baud | 1: 9,600 baud | baud rate |
| PD165 | 0: ASCII,8N1 | 3: RTU,8N1 | ASCII vs RTU,data bits,parity,stop bits |
page 60 describes the Modbus protocol
Online Resources
Huan Yang HY Series Inverter User Manual
https://www.exoror.com/datasheet/VFD.pdf
https://bulkman3d.com/wp-content/uploads/2019/01/HY01D523B-VFD-Manual.pdf
https://www.nvcnc.net/wp-content/uploads/2021/06/HuanYang-VFD-Manual.pdf
http://www.jinlantrade.com/ebay/invertermanual.pdf
Produts | Hyria Electric Co, LTD (Wayback Machine)
Releases · GilchristT/SpindleTalker2
RobertOlechowski/Huanyang_VFD: All you have to know about Huanyang VFD
linuxcnc/src/hal/user_comps/huanyang-vfd at master · LinuxCNC/linuxcnc
machinekit-hal/src/hal/user_comps/huanyang-vfd at master · machinekit/machinekit-hal